1、板式換熱器板型選擇
1 plate type plate selection
板片型式或波紋式應根據換熱場合的實際需要而定。對流量大允許壓降小的情況，應選用阻力小的板型，反之選用阻力大的板型。根據流體壓力和溫度的情況，確定選擇可拆卸式，還是釬焊式。確定板型時不宜選擇單板面積太小的板片，以免板片數量過多，板間流速偏小，傳熱系數過低，對較大的換熱器更應注意這個問題。
The plate type or corrugated type shall be determined according to the actual needs of the heat exchange situation. For large flow rate and small pressure drop, a small resistance plate shall be adopted, otherwise a large resistance plate shall be adopted. According to the fluid pressure and temperature, determine whether to choose removable or brazing type. When determining the plate shape, it is not suitable to choose the plate with too small single board area, so as to avoid excessive plate quantity, small flow velocity between the plates, and low heat transfer coefficient, which should be paid more attention to by the larger heat exchanger.
2、流程和流道的選擇
2. Selection of process and flow passage
流程指板式換熱器內一種介質同一流動方向的一組并聯流道，而流道指板式換熱器內，相鄰兩板片組成的介質流動通道。一般情況下，將若干個流道按并聯或串聯的方式連接起來，以形成冷、熱介質通道的不同組合。
A group of parallel flow heat exchanger in the process of the fingerboard of a medium with a flow direction, flow and fingerboard heat exchanger, two adjacent plates composed of medium flow channel. In general, a number of runners are connected in parallel or in series to form combinations of cold and hot medium passages.
流程組合形式應根據換熱和流體阻力計算，在滿足工藝條件要求下確定。盡量使冷、熱水流道內的對流換熱系數相等或接近，從而得到最佳的傳熱效果。因?yàn)樵趥鳠岜砻鎯蓚?cè)對流換熱系數相等或接近時傳熱系數獲得較大值。雖然板式換熱器各板間流速不等，但在換熱和流體阻力計算時，仍以平均流速進行計算。由于“U”形單流程的接管都固定在壓緊板上，拆裝方便。
The form of flow combination shall be determined according to the calculation of heat transfer and fluid resistance and meeting the requirements of process conditions. The convective heat transfer coefficient in the cold and hot water passages is equal or close as far as possible so as to achieve the best heat transfer effect. Because the convective heat transfer coefficient is equal or close to the two sides of the heat transfer surface, the heat transfer coefficient is larger. Although the flow velocity between plates of plate heat exchangers is unequal, the average flow velocity is calculated when the heat transfer and fluid resistance are calculated. Because the "U" shape, the single process of the nozzles are fixed on the compression plate, disassembly and assembly is convenient.
3、壓降校核
3 、 pressure drop check
在板式換熱器的設計選型使，一般對壓降有一定的要求，所以應對其進行校核。如果校核壓降超過允許壓降，需重新進行設計選型計算，直到滿足工藝要求為止。
In the plate heat exchanger design and selection, general pressure drop has a certain requirement, so it should be checked. If the check pressure drop exceeds the allowable pressure drop, the design selection calculation shall be carried out until the process requirements are met.
備案號：蘇ICP備17015414號-4 技術支持：
